河南省产业结构演化及其生态环境效应分析

文章分析了河南省产业发展轨迹以及不同产业发展对生态环境的影响,利用不同产业的生态环境影响指数计算了1980年以来该省产业结构演化的生态环境效应,得出河南省产业转型轨迹与产业转型引起的生态环境效应轨迹在变化趋势上存在着一致性、产业转型对生态环境的影响滞后于产业转型等结论,并提出一些基于生态环境保护的河南省经济持续发展的长效产业政策。     

T型氧化沟工艺处理低碳源生活污水的效果研究

详细介绍了T型氧化沟工艺的特征,并考察研究了该工艺处理低碳源生活污水的长期运行效果。研究结果表明,工艺出水COD、BOD5、NH3-N、TN和TP年平均浓度分别为13.9、3.8、0.91、18.80和1.67 mg/L,去除率分别为88.99%、94.37%、96.74%、37.57%和41.58%,均能达到相应的排放标准。由于T型氧化沟中以好氧环境为主,缺乏厌氧和缺氧环境以及进水的BOD5/TN值低,工艺对有机物及NH3-N的去除效果较好,但TN和TP去除效果较低。提出了加强工艺脱氮除磷的措施,为同类型污水处理厂改造提供参考。     

河道溢油事故环境风险评价中若干关键问题探讨

河道溢油事故已成为内河道突发性水环境污染的主要问题之一,尤其水源地突发性污染事件日益增多,对社会、经济和河道生态环境造成严重的不良影响。新建的水上项目必须通过溢油风险评价来分析项目建设投产后对周边的环境影响,目前溢油风险评价尚无统一的方法,且风险分析不够深入。本文基于国内外经典的油膜动力学模型及统计学等理论,明确溢油事故环境风险评价中事故源强、事故概率、溢油油膜影响范围、风险应急时间以及水厂吸水口关闭时间等几个关键问题的分析方法,以期进一步提高河道溢油事故的环境风险评价水平。     

论民初我国救灾之主要特征

民国初年我国救灾的主要特征有三:一是救灾主体多元化,这可从阶层、国籍、职业、身份等方面看出,总体上又可划分为政府和社会力量两个方面。至于救灾效能,无论是政府还是社会救济力量均存在着或多或少的局限性。二是短效机制占主导,这可从救灾因素之临设性、救灾甚于防灾两点看出。三是社会过渡性彰显,无论是思想,还是机构、制度,都呈现出明显的新旧交错性,即社会过渡性。     

基于事故统计分析的城市轨道交通运营安全和可靠性研究

本文通过对城市轨道交通运营事故的统计分析,研究了影响轨道交通运营安全和可靠性的主要因素,并构建了城市轨道交通运营安全保障体系,以为提高轨道交通运营安全和可靠性的研究提供依据。     

电催化氧化法处理阳离子染料废水的试验研究

以结晶紫作为阳离子染料,采用电催化氧化法对阳离子染料溶液进行了电解脱色处理试验,研究了电流密度、电解质种类、电解质浓度、pH值等对该溶液脱色率的影响,测定了电解时溶液中生成的余氯浓度和溶液的紫外-可见吸收光谱曲线,并对不同电解时间的溶液的吸光度进行了归一化计算。结果表明:随着电解时间的延长,水溶液中活性氯浓度不断上升,经一定时间后达到最大值;在电催化和活性氯的协同作用下,阳离子染料结晶紫分子中的大π共轭体系被破坏、苯环结构基本瓦解,溶液快速脱色;在电流密度为5.1mA/cm2、NaCl浓度为4g/L、pH值为9.41的条件下,初始浓度为100mg/L的结晶紫溶液经过20min的电解,其脱色率可高达98.31%。     

电沉积法处理电解锌漂洗废水的动力学研究

采用电沉积法处理电解锌漂洗工艺废水,以回收废水中的重金属资源。在不同实验条件下对电沉积反应过程中电沉积反应速率及其影响因素进行了研究,结果表明,电沉积回收重金属锌符合准一级动力学规律,当V=6 V时,速率常数k=0.0214。最佳实验条件为:槽电压V=6 V、电解时间为45~60 min、pH为2.5~3.5,反应过程中应充分搅拌。利用电沉积法处理电解锌漂洗废水,将重金属Zn2+还原为单质锌,处理废水的同时实现重金属资源的回收,在工业中有较好的应用前景。     

Effect of platinum on the photocatalytic degradation of chlorinated organic compound

TiO2 nanoparticles, doped with di erent Pt contents, were prepared by a modified photodeposition method using Degussa P-25 TiO2, H2PtCl6 6H2O and methanol as the solvents. The physicochemical properties of Pt/TiO2 were investigated by the nitrogen adsorption and desorption isotherm measurement technique, X-ray di raction analysis and photoluminescence spectra, respectively. Reaction rates from photocatalytic removal of dichloromethane over Degussa P-25 TiO2 and Pt/TiO2 were evaluated. The average diameter and BET surface area of the TiO2 catalyst particles were 300 nm and 50 m2/g, respectively. The degradation e ciency was 99.0%, 82.7%, 55.2%, and 57.9% with TiO2 at inlet concentrations of 50, 100, 200, and 300 ppm, respectively. And the degradation e ciency was 99.3%, 79.7%, 76.5%, and 73.4% with a 0.005 wt.% Pt/TiO2 at inlet concentrations of 50, 100, 200, and 300 ppm, respectively. In addition, we found that the photoluminescence emission peak intensities decreased with increases in the doping amount of Pt, which indicates that the irradiative recombination was weakened. Furthermore, the results showed that the UV/0.005 wt.% Pt/TiO2 process was capable of e ciently decomposing gaseous DCM in air.     

Adsorptive property of Cu^2＋-loaded montmorillonite clays for Escherichia coli K_（88） in vitro

The Cu²⁺-loaded montmorillonite clays (MMT-Cu) may be a good material for the adsorbed and eliminated pathogenic bacteria from aqueous solution.     

Ultrasonic preparation of nano-nickel/activated carbon composite using spent electroless nickel plating bath and application in degradation of 2,6-dichlorophenol

Ni was effectively recovered from spent electroless nickel （EN） plating baths by forming a nano-nickel coated activated carbon composite. With the aid of ultrasonication, melamine- formaldehyde-tetraoxalyl-ethylenediamine chelating resins were grafted on activated carbon （MFT/AG）. PdC12 sol was adsorbed on MFT/AC, which was then immersed in spent electroless nickel plating bath; then nano-nickel could be reduced by ascorbic acid to form a nano-nickel coating on the activated carbon composite （Ni/AC） in situ. The materials present were carefully examined by Fourier transform infrared spectroscopy, X-ray diffraction, field emission scanning electron microscopy, X-ray photoelectron spectroscopy and electro- chemistry techniques. The resins were well distributed on the inside and outside surfaces of activated carbon with a size of 120 ± 30 nm in MFT/AC, and a great deal of nano-nickel particles were evenly deposited with a size of 3.8 ± 1.1 nm in Ni/MFT. Moreover, Ni/AC was successfully used as a catalyst for ultrasonic degradation of 2.6-dichloronhenol.